TOWER grzejnik dekoracyjny

Decorative radiator TOWER

DECOR-3-1

The TOWER radiator, thanks to its unique construction, has increased power. It consists of two systems: the water system and the heat transfer system.
Water system – constructed from copper heating tubes horizontally arranged inside the heater and connected at the ends by vertical copper collectors. The connection of the heating tubes with the collectors is made by soldering (hard soldering). The heat transfer system – is made of aluminium sheet fins set vertically on the heating pipes of the water system. Appropriately bent front and back edges of the lamellas fit tightly together to form the front and back wall of the heater. A flat aluminium plate is mounted on the lamella wall – on both sides. Connection of copper and aluminium is a dry connection, therefore there is no electrochemical phenomenon in it.
The TOWER radiator is a slim, tall model available in a version with two visible vertical lines (a place where aluminium elements join) or in a version that is perfectly smooth on the front side and with visible lines on the back wall. The standard version is the version with visible lines on the front and back (the ordering process should precisely specify the type of radiator).

Small water capacity
Distance from the wall
Warranty
For condensing boilers
For heat pumps
Eco
Natural convection
Dynamic heating
Radiation of heat in all directions
Increased power

TOWER radiators are centrally powered from the bottom. The connection is immovable: connection block in the axis of the radiator, supply/return – freely, spacing between connections – 50 mm. Female thread ½ ‘’

TOWER radiators may be used in any type of installation – copper, plastic or traditional steel. They cooperate with electric, gas, oil and solid fuel boilers. They work perfectly with condensing boilers and in systems operated by heat pumps.

TOWER radiators are used in:

  • single and multi-family buildings – possibility to be supplied from the municipal network
  • energy-saving houses – possibility of using in every configuration of central heating system
  • frame and wooden houses – very light heaters mean easy transport and installation, even on plasterboard walls
  • educational, teaching and childcare buildings – low contact temperature
  • cultural buildings, bank service facilities – decorative radiator – narrow, vertical
  • sacral buildings – active air mixing, even temperature distribution, moisture removal
  • warehouses and large buildings, industrial buildings – the possibility of temporary temperature reduction and even switching off some zones with the option of quick activation
  • facilities with increased humidity, swimming pools, car washes, winter gardens, vessels and port infrastructure

Technical data
of the TOWER
radiator

Height: 1385, 1565, 1745, 1925 mm

Lenght: 400, 500, 600, 700, 800 mm

Width: 90 mm

Weight: 9,66-24,30 kg

Water capacity: 1,23-2,78 dm³

Distance between radiator and wall: 2 cm

Connections: bottom centre, 50 mm spacing

Operating pressure: 1,5 MPa

Operating temperature: up to +110°С

Advantages of TOWER radiator:

  • copper-aluminium construction ensures high efficiency at low flow temperatures
  • copper and aluminium are characterised by a high heat transfer coefficient (higher than steel and cast iron), heat is emitted even at a small temperature difference (heater and ambient)
  • corrugated, very large heat exchange surface, an important feature for heating based on a low temperature of the heating agent – condensation boilers, heat pumps
  • low own weight and small water capacity mean high heating dynamics, the heaters quickly reach their full rated power for a given flow temperature
  • low thermal inertia enables energy-efficient and easily controllable heating
  • Heating of the room takes place in a mixed way:
    – by intense, wide-angle heat radiation from the front corrugated surface of the heater
    – by convection

Air drawn in from below through the heater’s numerous convection chimneys flows through the heater’s interior, heats up after coming into contact with the surface of the pipes and fins and then flows out at the top through the perforated top casing. This double method of heat emission results in even heating of the air in the entire room.

Method of heat emission by REGULUS-system heaters

Illustration of the heat transfer by omnidirectional radiation from the surface – REGULUS-system heater

Illustration of heat transfer by perpendicular radiation from the surface – Finned aluminium heater

Any RAL colour included in the price

Colours from RAL K7 palette – powder varnish. Standard colour white – RAL 9003
Radiators in colours from the following colour chart (RAL K7) are available at list price, without an extra charge. An additional charge of 10% of the radiator’s list price shall apply to metallic colours, METALLIC version as well as convectors painted with structured paints.
The RAL K7 pattern book is available at our distributors.

NOTE: The colours displayed on the monitor may vary slightly from the actual RAL colours depending on the monitor’s parameters, therefore the presented list should be treated as indicative only! Please contact us by telephone to confirm colour matching.

Swimming pool version

SWIMMING POOL VERSION – these are special versions of wall mounted heaters intended for areas with increased humidity, such as swimming pools, car washes, laundries, conservatories, etc.
Their special resistance results from two features:
*construction – REGULUS®-system wall heaters are made of copper (exchanger) and aluminium (covers, lamellas), i.e. metals extremely resistant to corrosion. Unlike steel heaters, which quickly and easily succumb to destructive corrosion, copper and aluminium, when subjected to the process of oxidation, form oxides which, permanently connected to the non-oxidised material, constitute a tight protective layer for the process to continue deep into the structure of these metals.
*thickened layer of special varnish – an important protection, both against moisture and the impact of chemicals (used in swimming pools and other such facilities), is a durable, thickened layer of polyester-epoxy varnish hardened at high temperature. The mounting elements of the heaters are also made of aluminium profiles coated with facade powder varnish.

WARRANTY: 10 YEARS

POOL DESIGN PRICE = REGULAR PRICE OF THE HEATER – NO SURCHARGE – ATTENTION TEMPORARY PROMOTION

pool heaters
radiator pool
swimming pool version

The radiators are symmetrical, their front and back are identical. They are reversible, i.e. they can be installed with an approach (connection) from the left or right side.

Technical data of TOWER radiators

TypeHeight [mm]Lenght [mm]Thickness [mm]Power [W]
75/65/20
Power [W]
55/45/20
Power [W]
45/35/20
Water
capacity [l]
Weight [kg]
TOWER 14/040 13854009010556364261,239,66
TOWER 14/050 13855009014939006031,4211,7
TOWER 14/060 138560090192611617771,6113,5
TOWER 14/070 138570090231413959341,8315,3
TOWER 14/080 1385800902703162910912,0217,4
TOWER 16/04015654009011376854591,3510,6
TOWER 16/050 15655009016479936651,5612,9
TOWER 16/060 156560090215412988691,7715,1
TOWER 16/070 156570090262015791057217,3
TOWER 16/080 1565800903084185912452,2119,6
TOWER 18/040 17454009013668235511,5812,3
TOWER 18/050 174550090191311517721,8214,9
TOWER 18/060174560090245414799902,0717,1
TOWER 18/070 1745700902934176911842,3419,4
TOWER 18/0801745800903414205813782,5822
TOWER 20/040 19254009014488735841,713,3
TOWER 20/050192550090206812478351,9616,2
TOWER 20/060 1925600902682161710822,2318,8
TOWER 20/070 1925700903239195213072,5221,4
TOWER 20/080 1925800903794228715312,7824,3
 Room temperature
tztp581216202224
95900.5750.5950.6240.6560.6920.7110.731
850.5920.6130.6440.6780.7160.7370.758
800.6090.6320.6650.7010.7420.7640.788
750.6280.6520.6870.7260.7700.7940.819
700.6480.6740.7110.7530.8000.8260.854
90850.6100.6330.6650.7020.7430.7650.788
800.6290.6530.6880.7270.7710.7950.820
750.6490.6740.7120.7540.8010.8270.854
700.6700.6970.7370.7820.8340.8620.892
650.6920.7220.7650.8140.8690.90.933
85800.6490.6750.7120.7540.8020.8280.855
750.6710.6980.7380.7830.8340.8630.893
700.6930.7220.7660.8140.8700.9010.934
650.7170.7490.7950.8480.9090.9420.978
600.7430.7770.8280.8850.9510.9881.028
80750.6940.7230.7670.8150.8710.9020.935
700.7180.7500.7960.8490.9100.9430.980
650.7440.7780.8290.8860.9520.9891.029
600.7720.8090.8640.9260.9991.0401.084
550.8030.8420.9020.9701.0501.0961.145
75700.7450.7790.830.8870.9530.991.03
650.7730.8100.8650.9271.0001.0411.085
600.8040.8430.9030.9711.0521.0971.146
550.8360.8790.9441.0201.1091.1591.215
500.8720.9190.9901.0741.1731.2291.292
70650.8050.8440.9040.9731.0531.0981.148
600.8370.8810.9461.0211.1101.1611.216
550.8730.9200.9921.0751.1741.2311.294
500.9120.9641.0421.1351.2461.3101.382
450.9551.0111.0981.2021.3271.4011.483
65600.8740.9210.9931.0771.1761.2331.295
550.9130.9651.0441.1361.2481.3121.383
500.9561.0131.1001.2041.3291.4031.485
60550.9571.0141.1011.2051.3311.4051.487
501.0041.0671.1641.2811.4241.5091.604
451.0561.1261.2341.3671.5321.6301.742
401.1131.1911.3141.4651.6571.7721.906
55501.0581.1271.2361.3691.5341.6331.745
451.1151.1931.3161.4681.6591.7751.909
401.1791.2671.4071.5821.8071.9462.108
351.2521.3511.5111.7151.9842.1532.354
50451.1821.2691.4091.5851.8101.9492.112
401.2541.3531.5141.7181.9872.1572.358
351.3361.4491.6361.8772.2042.4142.670
301.4291.561.7782.0692.4732.7423.078
45401.3381.4521.6391.8812.2082.4192.675
351.4321.5631.7822.0732.4782.7483.084
301.5401.6931.9532.3082.8243.1813.642
40351.5431.6971.9572.3142.8313.1883.65
301.6691.8512.1662.6113.2923.7884.462
35301.8222.0412.4303.0063.9464.6815.759

Description:
tz – Flow temperature
tp – Return temperature

In the description of the heater parameters tz appears as the first value, tp as the second, and the room temperature as the third, e.g. 55/45/20

To calculate the heating power for non-standard supply parameters, divide the heating power for parameter 75/65/20 by the value read from the correction factor table.

For example, we are looking for the heating power for the S6/60 radiator for the parameter 70/50/20. The power for 75/65/20 is 922 W. In the table of correction factors, we read the coefficient for: tz = 70, tp = 50, room temperature = 20. In the table of correction coefficients read the value of the coefficient for: tz = 70, tp = 50, room temperature = 20. For these parameters the coefficient is: 1,246.
Therefore: 922/1,246 ≈740 W

HEATER ACCESSORIES SUPPLIED TOGETHER WITH THE RADIATOR, INCLUDED IN THE PRICE.

A set of wall hangers or a set of feet for floor mounting (one option to be selected), dowels, screws, air vent, in the bottom-supplied heaters a thermoregulatory valve with pre-adjustment, connection gaskets and installation manual.

WKŁADKA-1

THERMOSTAT VALVE INLET  – with presetting – valve type SFP-10-1N – manufacturer Vario Term, valve body permanently installed in the factory in types: SD and SDCG. Pre-setting key available at extra charge.

ODPOWIETRZNIK-1

AIR VENT – manual heater vent – ½”, opened with a spanner or a flathead screwdriver after pointing the faucet in the desired direction.

STOJAK-2

FLOOR STANDS  – almost any heater can be mounted as a floor stand – suitable for its height. The assembly kit includes two stands screwed to the floor + dowels and screws, two connection gaskets, assembly instructions

WIESZAK-1

UNIVERSAL WALL HANGS – one type for all types of radiators. The set includes two bottom brackets, two top profiles with stabilizing hooks, dowels, screws, two connection gaskets, assembly instructions. The distance between the radiator and the wall is 2 cm.

DECOR radiator control fittings and accessories

ZESTAW „TWINS” BIAŁY

“TWINS” WHITE – angle fitting left – with connection head
Spacing of connecting studs: 50 mm.
Product code: VATWBI

ZESTAW „TWINS” ZŁOTY

“TWINS” GOLD – angle fitting left – with connection head
Spacing of connecting studs: 50 mm.
Product code: VATWZL

ZESTAW „TWINS” SATYNA

“TWINS” SATINE – angle fitting left – with connection head
Spacing of connecting studs: 50 mm.
Product code: VATWSA

TWINS CZARNY

“TWINS” BLACK – angle fitting left – with connection head
Spacing of connecting studs: 50 mm.
Product code: VATWCZ

Heads – technical data:

range: 8°C-30°C (16°C-30°C)
max. ambient temp: 50°C
closing time: 24 min.
the effect of pressure difference: <0,2 K
hysteresis: 0.3 K
effect of the heating medium temperature: <0,5 K

The REGULUS®-system thermostatic head is a heater temperature regulator :

  • modern, ergonomic shape
  • allows to maintain the desired thermal comfort in the room, taking into account the heat gains from other sources, such as lighting or insolation
  • due to its construction it is easy to keep clean, which makes it suitable for rooms with high sanitary requirements.

Features of REGULUS-system thermostatic head:

  • reliable liquid sensor
  • control knob with digital marking
  • frost protection function 8°C
  • body made of high-quality plastic

WARRANTY CONDITIONS

 

25 YEARS WARRANTY!!!

REGULUS®-system radiators are covered by a 25-year warranty – the warranty covers the tightness of heaters water system. Heater lifespan is comparable to the lifespan of copper installations and may be even several dozen years!

WARRANTY CONDITIONS

REGULUS®-system spółka jawna (general partnership) with its registered office at 51 Grażyńskiego Street in Bielsko-Biała, Poland, gives a warranty for its products: REGULUS®-system water-filled radiators.

The Manufacturer declares that the REGULUS®-system radiators are made in accordance with the EN-442 European Standard.

The Manufacturer’s warranty covers the leaktightness of the radiator water system. The warranty period varies depending on the place of application, thus, it is:

25 YEARS for radiators for facilities with microclimates typical of residential premises, offices and the like.

10 YEARS for radiators for facilities with high moisture of air and an increased hygiene and health regime, like swimming pools, car washes, drying rooms, vessels, commercial premises and all kinds of industrial buildings, including the port infrastructure.

  1. This warranty does not affect any of the consumer’s statutory rights relating to the product type’s incompatibility with the sales agreement.
  2. The User’s rights under this warranty may only be exercised via the company, from which the product was purchased. They may be exercised directly at the Manufacturer’s only if the point of sale, in which the product was purchased, has been closed down.
  3. This warranty shall be valid from the date of purchase as specified in the purchase document. The User’s rights under this warranty may only be exercised upon production of the purchase document along with the confirmed Warranty Card.
  4. If an event covered by the warranty occurs in the warranty period, the complaining User can demand the radiator to be replaced with another one of the same type.
  5. The new product shall be given to the User at the place of defect notification within 14 days from the date of notification. On reception of the new product, the User shall return the faulty radiator, unless the event has occurred during the ongoing heating season. In such a case, the faulty radiator shall be returned after the actual replacement.
  6. The Manufacturer shall cover the costs of the replacement of the faulty radiator with a new, fault-free one after receiving the relevant bill. The costs of this service shall be agreed on between the Manufacturer and the User in advance.
  7. Warranties for the control fittings shall be provided by their respective manufacturers.
  8. The Manufacturer’s warranty does not cover the functions and durability built in the thermostatic valves in bottom-fed radiators. These are covered by their manufacturer’s warranties.

ITEMS NOT COVERED BY THIS WARRANTY

  1. Any defects resulting from misuse of the product. Permissible system operating parameters: Water temperature – 110 °C, operating pressure – 1.5 MPa.
  2. Leakages resulting from incorrect installation of the radiator, the valve air vent or their components, and particularly from defrosting or using wrong sealing materials. Side-fed radiators are fitted with a rotatable half union for front sealing with gaskets.
  3. Defects and inconveniences resulting from incorrect installation or incorrect plumbing adjustment of the radiator and system water pollution.
  4. Mechanically damaged products (in particular with traces of impact, scratches, dents, twists – e.g. air vent or pipe sockets) shall not be subject to replacement.
  5. The warranty shall be void when the User or anyone else modifies or repairs any product of the REGULUS®-system company without authorization.
  6. The warranty shall be void when the mechanical filter mounted on the power supply of the central heating system, to which the REGULUS®-system radiators are connected, is removed. This particularly refers to a system with steel components.
  7. The REGULUS®-system company reserves the right to modify its products without prior notice.

ITEMS NOT AFFECTING THE WARRANTY

  1. Any kind of divisor mounted on the external surface of REGULUS®-system radiators, provided this does not damage the radiator water system.
  2. REGULUS®-system radiators mounted within open central heating systems.
  3. Radiators mounted within systems supplied directly by the municipal heat distribution network, not by way of a heat exchanger.
  4. Periodic emptying of the central heating system, provided the other system components allow for such an operation and the operation will not make the components corrode.

The User receiving the product together with the Warranty Card accepts all the above warranty terms. 

Type of connection

The radiators are symmetrical, their front and back are identical. They are reversible, i.e. they can be installed with an approach (connection) from the left or right side.

Technical data

Technical data of TOWER radiators

TypeHeight [mm]Lenght [mm]Thickness [mm]Power [W]
75/65/20
Power [W]
55/45/20
Power [W]
45/35/20
Water
capacity [l]
Weight [kg]
TOWER 14/040 13854009010556364261,239,66
TOWER 14/050 13855009014939006031,4211,7
TOWER 14/060 138560090192611617771,6113,5
TOWER 14/070 138570090231413959341,8315,3
TOWER 14/080 1385800902703162910912,0217,4
TOWER 16/04015654009011376854591,3510,6
TOWER 16/050 15655009016479936651,5612,9
TOWER 16/060 156560090215412988691,7715,1
TOWER 16/070 156570090262015791057217,3
TOWER 16/080 1565800903084185912452,2119,6
TOWER 18/040 17454009013668235511,5812,3
TOWER 18/050 174550090191311517721,8214,9
TOWER 18/060174560090245414799902,0717,1
TOWER 18/070 1745700902934176911842,3419,4
TOWER 18/0801745800903414205813782,5822
TOWER 20/040 19254009014488735841,713,3
TOWER 20/050192550090206812478351,9616,2
TOWER 20/060 1925600902682161710822,2318,8
TOWER 20/070 1925700903239195213072,5221,4
TOWER 20/080 1925800903794228715312,7824,3
Correction coefficients
 Room temperature
tztp581216202224
95900.5750.5950.6240.6560.6920.7110.731
850.5920.6130.6440.6780.7160.7370.758
800.6090.6320.6650.7010.7420.7640.788
750.6280.6520.6870.7260.7700.7940.819
700.6480.6740.7110.7530.8000.8260.854
90850.6100.6330.6650.7020.7430.7650.788
800.6290.6530.6880.7270.7710.7950.820
750.6490.6740.7120.7540.8010.8270.854
700.6700.6970.7370.7820.8340.8620.892
650.6920.7220.7650.8140.8690.90.933
85800.6490.6750.7120.7540.8020.8280.855
750.6710.6980.7380.7830.8340.8630.893
700.6930.7220.7660.8140.8700.9010.934
650.7170.7490.7950.8480.9090.9420.978
600.7430.7770.8280.8850.9510.9881.028
80750.6940.7230.7670.8150.8710.9020.935
700.7180.7500.7960.8490.9100.9430.980
650.7440.7780.8290.8860.9520.9891.029
600.7720.8090.8640.9260.9991.0401.084
550.8030.8420.9020.9701.0501.0961.145
75700.7450.7790.830.8870.9530.991.03
650.7730.8100.8650.9271.0001.0411.085
600.8040.8430.9030.9711.0521.0971.146
550.8360.8790.9441.0201.1091.1591.215
500.8720.9190.9901.0741.1731.2291.292
70650.8050.8440.9040.9731.0531.0981.148
600.8370.8810.9461.0211.1101.1611.216
550.8730.9200.9921.0751.1741.2311.294
500.9120.9641.0421.1351.2461.3101.382
450.9551.0111.0981.2021.3271.4011.483
65600.8740.9210.9931.0771.1761.2331.295
550.9130.9651.0441.1361.2481.3121.383
500.9561.0131.1001.2041.3291.4031.485
60550.9571.0141.1011.2051.3311.4051.487
501.0041.0671.1641.2811.4241.5091.604
451.0561.1261.2341.3671.5321.6301.742
401.1131.1911.3141.4651.6571.7721.906
55501.0581.1271.2361.3691.5341.6331.745
451.1151.1931.3161.4681.6591.7751.909
401.1791.2671.4071.5821.8071.9462.108
351.2521.3511.5111.7151.9842.1532.354
50451.1821.2691.4091.5851.8101.9492.112
401.2541.3531.5141.7181.9872.1572.358
351.3361.4491.6361.8772.2042.4142.670
301.4291.561.7782.0692.4732.7423.078
45401.3381.4521.6391.8812.2082.4192.675
351.4321.5631.7822.0732.4782.7483.084
301.5401.6931.9532.3082.8243.1813.642
40351.5431.6971.9572.3142.8313.1883.65
301.6691.8512.1662.6113.2923.7884.462
35301.8222.0412.4303.0063.9464.6815.759

Description:
tz – Flow temperature
tp – Return temperature

In the description of the heater parameters tz appears as the first value, tp as the second, and the room temperature as the third, e.g. 55/45/20

To calculate the heating power for non-standard supply parameters, divide the heating power for parameter 75/65/20 by the value read from the correction factor table.

For example, we are looking for the heating power for the S6/60 radiator for the parameter 70/50/20. The power for 75/65/20 is 922 W. In the table of correction factors, we read the coefficient for: tz = 70, tp = 50, room temperature = 20. In the table of correction coefficients read the value of the coefficient for: tz = 70, tp = 50, room temperature = 20. For these parameters the coefficient is: 1,246.
Therefore: 922/1,246 ≈740 W

Accessories included

HEATER ACCESSORIES SUPPLIED TOGETHER WITH THE RADIATOR, INCLUDED IN THE PRICE.

A set of wall hangers or a set of feet for floor mounting (one option to be selected), dowels, screws, air vent, in the bottom-supplied heaters a thermoregulatory valve with pre-adjustment, connection gaskets and installation manual.

WKŁADKA-1

THERMOSTAT VALVE INLET  – with presetting – valve type SFP-10-1N – manufacturer Vario Term, valve body permanently installed in the factory in types: SD and SDCG. Pre-setting key available at extra charge.

ODPOWIETRZNIK-1

AIR VENT – manual heater vent – ½”, opened with a spanner or a flathead screwdriver after pointing the faucet in the desired direction.

STOJAK-2

FLOOR STANDS  – almost any heater can be mounted as a floor stand – suitable for its height. The assembly kit includes two stands screwed to the floor + dowels and screws, two connection gaskets, assembly instructions

WIESZAK-1

UNIVERSAL WALL HANGS – one type for all types of radiators. The set includes two bottom brackets, two top profiles with stabilizing hooks, dowels, screws, two connection gaskets, assembly instructions. The distance between the radiator and the wall is 2 cm.

Accessories

DECOR radiator control fittings and accessories

ZESTAW „TWINS” BIAŁY

“TWINS” WHITE – angle fitting left – with connection head
Spacing of connecting studs: 50 mm.
Product code: VATWBI

ZESTAW „TWINS” ZŁOTY

“TWINS” GOLD – angle fitting left – with connection head
Spacing of connecting studs: 50 mm.
Product code: VATWZL

ZESTAW „TWINS” SATYNA

“TWINS” SATINE – angle fitting left – with connection head
Spacing of connecting studs: 50 mm.
Product code: VATWSA

TWINS CZARNY

“TWINS” BLACK – angle fitting left – with connection head
Spacing of connecting studs: 50 mm.
Product code: VATWCZ

Heads – technical data:

range: 8°C-30°C (16°C-30°C)
max. ambient temp: 50°C
closing time: 24 min.
the effect of pressure difference: <0,2 K
hysteresis: 0.3 K
effect of the heating medium temperature: <0,5 K

The REGULUS®-system thermostatic head is a heater temperature regulator :

  • modern, ergonomic shape
  • allows to maintain the desired thermal comfort in the room, taking into account the heat gains from other sources, such as lighting or insolation
  • due to its construction it is easy to keep clean, which makes it suitable for rooms with high sanitary requirements.

Features of REGULUS-system thermostatic head:

  • reliable liquid sensor
  • control knob with digital marking
  • frost protection function 8°C
  • body made of high-quality plastic
Warranty

WARRANTY CONDITIONS

 

25 YEARS WARRANTY!!!

REGULUS®-system radiators are covered by a 25-year warranty – the warranty covers the tightness of heaters water system. Heater lifespan is comparable to the lifespan of copper installations and may be even several dozen years!

WARRANTY CONDITIONS

REGULUS®-system spółka jawna (general partnership) with its registered office at 51 Grażyńskiego Street in Bielsko-Biała, Poland, gives a warranty for its products: REGULUS®-system water-filled radiators.

The Manufacturer declares that the REGULUS®-system radiators are made in accordance with the EN-442 European Standard.

The Manufacturer’s warranty covers the leaktightness of the radiator water system. The warranty period varies depending on the place of application, thus, it is:

25 YEARS for radiators for facilities with microclimates typical of residential premises, offices and the like.

10 YEARS for radiators for facilities with high moisture of air and an increased hygiene and health regime, like swimming pools, car washes, drying rooms, vessels, commercial premises and all kinds of industrial buildings, including the port infrastructure.

  1. This warranty does not affect any of the consumer’s statutory rights relating to the product type’s incompatibility with the sales agreement.
  2. The User’s rights under this warranty may only be exercised via the company, from which the product was purchased. They may be exercised directly at the Manufacturer’s only if the point of sale, in which the product was purchased, has been closed down.
  3. This warranty shall be valid from the date of purchase as specified in the purchase document. The User’s rights under this warranty may only be exercised upon production of the purchase document along with the confirmed Warranty Card.
  4. If an event covered by the warranty occurs in the warranty period, the complaining User can demand the radiator to be replaced with another one of the same type.
  5. The new product shall be given to the User at the place of defect notification within 14 days from the date of notification. On reception of the new product, the User shall return the faulty radiator, unless the event has occurred during the ongoing heating season. In such a case, the faulty radiator shall be returned after the actual replacement.
  6. The Manufacturer shall cover the costs of the replacement of the faulty radiator with a new, fault-free one after receiving the relevant bill. The costs of this service shall be agreed on between the Manufacturer and the User in advance.
  7. Warranties for the control fittings shall be provided by their respective manufacturers.
  8. The Manufacturer’s warranty does not cover the functions and durability built in the thermostatic valves in bottom-fed radiators. These are covered by their manufacturer’s warranties.

ITEMS NOT COVERED BY THIS WARRANTY

  1. Any defects resulting from misuse of the product. Permissible system operating parameters: Water temperature – 110 °C, operating pressure – 1.5 MPa.
  2. Leakages resulting from incorrect installation of the radiator, the valve air vent or their components, and particularly from defrosting or using wrong sealing materials. Side-fed radiators are fitted with a rotatable half union for front sealing with gaskets.
  3. Defects and inconveniences resulting from incorrect installation or incorrect plumbing adjustment of the radiator and system water pollution.
  4. Mechanically damaged products (in particular with traces of impact, scratches, dents, twists – e.g. air vent or pipe sockets) shall not be subject to replacement.
  5. The warranty shall be void when the User or anyone else modifies or repairs any product of the REGULUS®-system company without authorization.
  6. The warranty shall be void when the mechanical filter mounted on the power supply of the central heating system, to which the REGULUS®-system radiators are connected, is removed. This particularly refers to a system with steel components.
  7. The REGULUS®-system company reserves the right to modify its products without prior notice.

ITEMS NOT AFFECTING THE WARRANTY

  1. Any kind of divisor mounted on the external surface of REGULUS®-system radiators, provided this does not damage the radiator water system.
  2. REGULUS®-system radiators mounted within open central heating systems.
  3. Radiators mounted within systems supplied directly by the municipal heat distribution network, not by way of a heat exchanger.
  4. Periodic emptying of the central heating system, provided the other system components allow for such an operation and the operation will not make the components corrode.

The User receiving the product together with the Warranty Card accepts all the above warranty terms. 

Download